background image

12 

TTH200 

 HEAD-MOUNT TEMPERATURE TRANSMITTER  |  OI/TTH200-EN REV. B 

 

 

4

 

Design and function 

General 

 

Digital transmitters are communication-ready devices with 
microprocessor-controlled electronics. They conform to the 
requirements of IP rating IP 20 and are suited for integration 
into DIN A and DIN B sensor heads. 
In the HART® transmitter, an FSK signal is superimposed on the 
4 to 20 mA output signal in accordance with the HART standard 
to facilitate bidirectional communication. 
The transmitters can be configured, polled, and tested using a 
DTM, an EDD or using the Field Information Manager (FIM). 
Handheld terminals can also be used for communication 
purposes. 
As an option, the transmitter can be fitted with a type AS LCD 
display. The LCD display is used exclusively for visualizing 
current process values. The electrical connection between the 
LCD display and transmitter is provided by a 6-pin flat ribbon 
cable with a plug connector. The LCD display can only be 
operated when connected to transmitters that have an LCD 
display interface. 
 

Note 

The HMI type A LCD indicator with configuration function 
optionally used with the TTH300 is not compatible with the 
TTH200. 
 

 

 

5

 

Product identification 

Name plate 

 

 

Note 

 

Products that are marked with the adjacent symbol 
may 

not

 be disposed of as unsorted municipal waste 

(domestic waste). 
They should be disposed of through separate 
collection of electric and electronic devices. 

 

 

Note 

The ambient temperature range 

n

 provided on the name plate 

refers only to the transmitter itself and not to the sensor 
element used in the measuring inset. 
 

 

1

  Manufacturer, manufacturer address, manufacturing year - week 

2

  Safety integrity level, SIL logo (optional with HART transmitter) 

3

  CE mark (EU conformity), if not on additional plate 

4

  Type designation / model 

5

  Transmitter communications protocol (HART) 

6

  2D barcode for serial number in accordance with order 

7

  7-digit serial number of the device electronic unit 

8

 Software revision 

9

 Hardware version 

j

  ‘Follow product documentation’ symbol 

k

  Set measuring range of the transmitter 

l

  Measuring point tag (TAG) in accordance with order (optional) 

m

  Set sensor type and circuit type 

n

  Ambient temperature range, on additional plate for Ex versions 

o

  Transmitter specification (supply voltage range, output current range, 

communications protocol) 

p

  Coding of the type of protection of the device (in accordance with 

ordering information) 

q

  Serial number of the device (serial number in accordance with order) 

 

Figure 7:  Name plate (example) 

 

 

Summary of Contents for TTH200

































Reviews: