ABB TPS48-H33 Operation Manual Download Page 64

Page: 64 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Operation and service

Page 34 / 99

HZTL4037_EN

Revision A

August 2016

5.3

Expected replacement intervals

Rotating components

The recommended replacement intervals for compressor and turbine wheels are specified

based on the safety concept for rotating parts (SIKO) and dependent on the operating condi-

tions. These intervals are shown on the rating plate of the turbocharger.

Non-rotating components

Depending on the system-specific operating conditions, a differentiation must be made be-

tween the intervals to be expected for:



replacing the bearing parts and



replacing the non-rotating components exposed to hot gas.

A decisive role is played by various influencing parameters which, in extreme cases, can dras-

tically shorten the replacement interval of these parts.

During the prescribed periodic service work, the individual parts are examined for wear and

replaced if necessary.

Component

GAS / MDO

Turbine casing

25000 … 50000

Nozzle ring

25000 … 50000

Heat sheet metal

25000 … 50000

Rotating components

See rating plate data

Bearing parts

12000 … 24000

Other casings

50000

Table 10: Expected replacement intervals [h]

GAS

= Gas

MDO = Marine Diesel Oil

The specified values are guideline values and not guaranteed values, see Influencing parameters.

Summary of Contents for TPS48-H33



































































































































Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands

ABB TPS48-H33, Operation Manual

Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands