ABB TPS48-H33 Operation Manual Download

Page: 42 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Removing and Installing

Page 12 / 99

HZTL4037_EN

Revision A

August 2016

2.2

Removing the turbocharger

WARNING

Danger of burns
Touching hot surfaces or contact with hot operating fluids can cause burns.



Do not touch hot surfaces. Observe the warning plate on the turbo-

charger.



Wear heat-resistant safety gloves and protective clothing.



Wait for the turbocharger to cool down before carrying out any work.

Wear safety gloves to protect against thermal hazards.

CAUTION

Do not strain cables
If you pull the speed measurement cables too hard, contacts can be pulled

out.



Do not strain the speed measurement cables by pulling.

NOTICE

Gas outlet casing (61001)
The gas outlet casing (61001) can remain fitted in the exhaust gas pipe if the

locking to the turbine casing is accessible. Otherwise the complete turbo-

charger unit including gas outlet casing must be removed.



Disconnect all pipes according to the instructions of the enginebuilder.

Version with water-cooled bearing casing:



Loosen and remove water connections.



Close the openings of the water connections with screw plugs.

Summary of Contents for TPS48-H33



































































































































Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands

ABB TPS48-H33, Operation Manual

Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands