ABB TPS48-H33 Operation Manual Download | Manualshive

Page: 100 / 130

background image

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

9

Dismantling and fitting

Page 70 / 99

© Copyright 2016 ABB. All rights reserved.

HZTL4037_EN

Revision A

August 2016

Removing the cartridge group

NOTICE

Loosening the turbine casing with the press-off tool
If the turbine casing cannot be loosened, it can be pressed off against the

bearing casing with the press-off tool (90042). See section Pressing off the

Figure 25: Removing cartridge group 2

1.  Insert screws from service support into cartridge group.
2.  Secure ring nuts (VRM) onto the screws with washers.
3.  Secure the lifting gear to the ring nuts and swivel lifting eye as shown.
4.  Remove the cartridge group vertically from the turbine casing.

«
...
98
99
100
101
102
...
»

Summary of Contents for TPS48-H33



































































































































Reviews:

No comments

Related manuals for TPS48-H33

Brand: Landoll Pages: 34

Brand: lancer Pages: 12

Brand: Eazyzap Pages: 32

Brand: Obdstar Pages: 42

PORTABLE ICE FISHING KIT

Brand: Garmin Pages: 5

Brand: Zennio Pages: 3

Brand: GE Pages: 18

Brand: Valko Pages: 10

Brand: MacDon Pages: 238

Brand: Martin Pages: 202

Brand: Harris Pages: 21

Brand: Billy Goat Pages: 14

ARIEDO HDC 300W

Brand: GSi Pages: 28

Brand: Nippon Genetics Pages: 14

Groline HI981412

Brand: Hanna Instruments Pages: 44

Brand: TEUCER Pages: 4

Brand: Barkey Pages: 72

Brand: BOCK Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands