ABB TPL65VA32 Operation Manual Download

Page: 68 / 124

Operation Manual / TPL65VA32/33

Maintenance

Cleaning components mechanically

5.5

Page 66

ber

2016

L2464_

ion

Cleaning the cartridge group on the turbine end

Soaking the contamination

Baked layers of contamination from fuel residue or coked oil may occur at

the turbine end. The contamination can be removed by soaking and

brushing. The procedure for soaking the layers of contamination as well

as for cleaning the turbine are described in the following.

To soften the layers of contamination on the turbine, the cartridge group

can be submerged vertically in a tank with liquid.

The cartridge group must be rotated to do this.



Two cranes (or chain blocks) must be used for the rotating operation.

Suspending the chain block directly from the crane and rotating the car-

tridge group is not permitted because of the risk of damage to the com-

pressor wheel.

Cartridge group with a central suspension point

CAUTION

Damage to compressor wheel
The lifting gear must not touch the compressor wheel at any time during

rotation.



Choose appropriate lifting gear length.

5.5.4

Summary of Contents for TPL65VA32





























































































































Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands

ABB TPL65VA32, Operation Manual

Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands