ABB TPL65VA32 Operation Manual Download

Page: 121 / 124

Operation Manual / TPL65VA32/33

Spare parts

Ordering spare parts

12.1

Page 119

ber

2016

L2464_

ion

Spare parts

Ordering spare parts

12.1

When making inquiries or ordering spare parts, the following data must be

specified:



Turbocharger type



Serial number (HT……)



Description and part number

Spare parts can be ordered from an official ABB Turbocharging Service

Station.



If different design versions have not been taken into consideration in

this document, please contact an ABB Turbocharging Service Station.

CAUTION

Storage of spare parts
All spare parts ordered with the turbocharger must be kept complete

and ready for use.



Parts showing signs of rust should be carefully cleaned and greased.



Dispose of replaced and unusable parts in a professional and envi-

ronmentally compatible way.

Required customer spare part set (97070)

Quantity

Description

Part number

Hexagon-head screw

42059

Verbus Ripp® washer

42058

Hexagon-head screw

61056 / 61059

Verbus Ripp® washer

61057 / 61058

Hexagon nut

61037

Gasket

42041

Gasket

42045

O-ring

42012

O-ring

77005

O-ring

86506

12.1

Summary of Contents for TPL65VA32





























































































































Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands

ABB TPL65VA32, Operation Manual

Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands