background image

L3692  

Tmax T8

11/39

Doc N°

Mod.

Apparatus

Scale

Page N°

1SDH000682R0002 

L3885

L5757  

3

5

6

3

1

Fig. 16

Press

Fig. 17

Press

d)   Circuit-breaker opening 

Press the push-button “O” (1) to open the circuit-breaker in the manual mode. When there is a shunt opening release, the operation can also 
be carried out in the remote mode by means of the special control circuit. The open state is signalled by the appearance of the letter “O” in the 
indicator (3).

 c)   Circuit-breaker closing

This operation can only be carried out when the closing springs are fully loaded.
Press the push-button (5) marked with the letter “I” for closing in the manual mode. When there is a shunt closing release, the operation can also 
be carried out in the remote mode by means of the special control circuit. Closing is signalled by the relative indicator (3), which moves to the 
“I” position. Moreover, the indicator of the state of the springs (6) moves to the WHITE position.  The control has enough energy for the opening 
operation even when the closing springs are unloaded. If present, the gearmotor immediately begins the automatic spring loading operation.

Summary of Contents for Tmax T8 L3692








































Reviews: