Important: Carefully read this installation manual before installing or using the fitting. This
installation manual provides important information about the correct installation, use,
maintenance and disposal of this product.
Please observe the following guidelines
1.
The fitting should only be installed by qualified personnel and installation must be in accordance
with AS/NZS 3000 and local regulations.
2.
This product may not be modified in any way what so ever or used for a purpose or in an environment
other than for which it is designed. Failing to observe these guidelines will invalidate the warranty
and the compliance of this product.
3.
Before installing the fitting, the supply must be isolated.
4.
The light source in this fitting is non-replaceable.
Installing and connecting
1.
This fitting should be connected to the voltage equivalent to that indicated on the type label. This
fitting is fitted with a terminal block suitable for loop-in-loop-out connection. The earth terminal
is provided for convenience of wiring through only and should not form part of any protective
shield. For further information on the different connection possibilities, see the instructions in
this installation manual.
Installation instructions
Important: Triangular markings indicate how to place the e-box with respect to the first-fix. Check
correct orientation before placing first-fix.
Connecting
Exploded view
Connecting
Connect
230 - 240V 50Hz
MAX 10A
138
43
Niet continu
Non-maintained
Non continu
Continu
Maintained
Continu
Maintained
2
Screw
1
Ceiling
3
Close wire cover
5
Place pictograph plates
4
Place e-box
6
Screw
Wall
4
3
5
Close wire cover
Place e-box
Screw
Triangular markings indicate how to place the e-box with respect to the first fix.
Check correct orientation before placing first fix.
PLEASE NOTE!
!
!
Cable size
max. 4 x 2.5mm²
strip 8mm
Accessories
Junction box cover
Spacer
Erklärung - Explanations
Exploded view
Connect mains
240V / 50Hz
Initial energising
After 24 hours the luminaire is fully commissioned.
blink
blink
wait
60h
24h
100%
0-30%
Only self-contained luminaires
First Fix
Wall bracket
E-box
Lightguide
Explanations
blink
blink
OK
Emergency mode
In test
Failure
Non-maintained
Maintained
Switched
maintained
Ceiling
Wall
Connecting
max. 4 x 2,5 mm²
Connect
230 - 240V 50Hz
MAX 10A
138
43
Niet continu
Non-maintained
Bereitschaftsschaltung
Non continu
Non-maintained
Continu
Maintained
Dauerschaltung
Continu
Maintained
Geschakeld
Switch-maintained
Geschaltet
Couplé
Switched maintained
CIS /
BUS / MD
DIM /
CINEMA
+ -
+ -
2
Screw
1
Ceiling
3
Close wire cover
5
Place pictograph plates
4
Place e-box
6
Screw
Wall
4
3
5
Close wire cover
Place e-box
Screw
Triangular markings indicate how to place the e-box with respect to the first fix.
Check correct orientation before placing first fix.
PLEASE NOTE!
!
!
Connecting
max. 4 x 2,5 mm²
Connect
230 - 240V 50Hz
MAX 10A
138
43
Niet continu
Non-maintained
Bereitschaftsschaltung
Non continu
Non-maintained
Continu
Maintained
Dauerschaltung
Continu
Maintained
Geschakeld
Switch-maintained
Geschaltet
Couplé
Switched maintained
CIS /
BUS / MD
DIM /
CINEMA
+ -
+ -
2
Screw
1
Ceiling
3
Close wire cover
5
Place pictograph plates
4
Place e-box
6
Screw
Wall
4
3
5
Close wire cover
Place e-box
Screw
Triangular markings indicate how to place the e-box with respect to the first fix.
Check correct orientation before placing first fix.
PLEASE NOTE!
!
!
Connecting
max. 4 x 2,5 mm²
Connect
230 - 240V 50Hz
MAX 10A
138
43
Niet continu
Non-maintained
Bereitschaftsschaltung
Non continu
Non-maintained
Continu
Maintained
Dauerschaltung
Continu
Maintained
Geschakeld
Switch-maintained
Geschaltet
Couplé
Switched maintained
CIS /
BUS / MD
DIM /
CINEMA
+ -
+ -
2
Screw
1
Ceiling
3
Close wire cover
5
Place pictograph plates
4
Place e-box
6
Screw
Wall
4
3
5
Close wire cover
Place e-box
Screw
Triangular markings indicate how to place the e-box with respect to the first fix.
Check correct orientation before placing first fix.
PLEASE NOTE!
!
!
Connecting
Connect
230 - 240V 50Hz
MAX 10A
138
43
Niet continu
Non-maintained
Non continu
Continu
Maintained
Continu
Maintained
2
Screw
1
Ceiling
3
Close wire cover
5
Place pictograph plates
4
Place e-box
6
Screw
Wall
4
3
5
Close wire cover
Place e-box
Screw
Triangular markings indicate how to place the e-box with respect to the first fix.
Check correct orientation before placing first fix.
PLEASE NOTE!
!
!
Cable size
max. 4 x 2.5mm²
strip 8mm
Important: 24 hours is required to allow the fitting battery to reach full capacity, ie: prior to a
discharge test. As the installer, it is your responsibility to conduct the initial discharge testing of
the installed fitting. Refer to AS/NZS 2293.
Testing precautions
Once the fitting is permanently connected to the
mains supply, a commissioning discharge test as
required in AS/NZS 2293.2 must be carried out.
You will need to allow 24 hours for the battery to
fully charge prior to conducting this test,
presently (at the time of writing), the standard
requires that fittings operate in emergency mode
for a period not less than 2 hours for their
commissioning test and for not less than 90
minutes thereafter (it is required that 6 monthly
discharge tests be carried out). You will need to
keep the records for the commissioning test and
enter them into the building emergency services
logbook or via other recording methods as
allowed by AS/NZS 2293.2.
Construction sites
Continuously switching off the mains power
supply that is connected to emergency light
fittings during the construction phase of an
installation will cause these fittings to discharge
and charge their batteries many times over a
short period; this can shorten life of the battery.
ABB does not recommend such practices and
may not honour the warranty on batteries when
they are subjected to such harsh operating
conditions. Emergency light fittings are designed
to be discharge tested once every 6 months as
per AS/NZS 2293.2, subjecting the product to
repeated discharge or charge cycles is regarded
as an abuse of the fittings.
1.
Evago mains wiring brown to (active), blue to (neutral), white to (DALI +) and black to (DALI -).
