background image

Health & Safety

Safety precautions

Be sure to read, understand and follow the instructions contained within this manual before and during use of the equipment. Failure
to do so could result in bodily harm or damage to the equipment.

Potential safety hazards

Electrical

Safety standards

This product has been designed to satisfy the requirements of IEC61010-1:2010 3rd edition 'Safety Requirements for Electrical
Equipment for Measurement, Control and Laboratory Use' and complies with US NEC 500, NIST and OSHA.

Safety conventions

EC Directive 89/336/EEC

Electrical

– In order to meet the requirements of the EC Directive 89/336/EEC for EMC regulations, this product must not be used in

an industrial environment.

End-of-life disposal

Cleaning

The complete recorder can be hosed down if it has been installed to IP66 / NEMA 4X standards – see Section 2, page 4. Warm water
and a mild detergent can be used.

Warning.

Installation and maintenance of this product must only be conducted by personnel authorized to work on electrical

installations and in accordance with relevant local regulations.

Warning.

To ensure safe use when operating this equipment, the following points must be observed:

Up to 240V AC may be present. Be sure to isolate the supply before removing the terminal cover.

Normal safety precautions must be taken to avoid the possibility of an accident occurring when operating in conditions of
high pressure and / or temperature.

Safety advice concerning the use of the equipment described in this manual or any relevant Material Safety Data Sheets (where
applicable) can be obtained from the Company, together with servicing and spares information.

Warning.

In this manual, a warning is used to indicate a condition which, if not met, could cause serious personal injury and / or

death. Do not proceed beyond a warning until all conditions have been met.

Caution.

A caution is used to indicate a condition which, if not met, could cause minor or moderate personal injury and / or

damage to the equipment. Do not proceed beyond a caution until all conditions have been met.

Note.

A note is used to indicate important information or instructions that should be considered before operating the equipment.

The recorder contains a small lithium battery that must be removed and disposed of responsibly in accordance with
local environmental regulations.

The remainder of the recorder does not contain any substance that causes undue harm to the environment and must be
disposed of in accordance with the Directive on Waste Electrical and Electronic Equipment (WEEE). It must not be
disposed of in Municipal Waste Collection.

2

CI/RVG200–EN

Summary of Contents for ScreenMaster RVG200

















Reviews: