ABB SafeRing Installation Instructions Manual Download Page 2

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third 
parties without express authority is strictly forbidden. © ABB Technology Ltd. 

General Safety Instructions!

 

 

Check that the installation, putting into service and 
maintenance of this apparatus is carried out by qualified 
personnel with knowledge of the apparatus to be installed. All 
the procedures as laid out in this installation and service 
instruction manual must be known. 

 

To perform the following installation requires a vocational 
training (electrician, electrical engineer) and some years of 
experience. 

 

Make sure the standard and legal prescriptions are adhered to 
during the installation, putting into service and maintenance. 
All procedures must be carried out in strict compliance to the 
rules of good working practice and safety at the work site. 

 

Please read this instruction manual and plan the work before 
starting the installation. 

 

Strictly follow the information given in this instruction manual. 

 

Pay special attention to the danger notes as indicated in this 
manual by the following symbol: 

 

 

 
 
 
 
 
 
 
 

Check and ensure that the personnel operating the apparatus 
have the instruction manual at hand, as well as the necessary 
information for correct installation. 

 

Before starting the retrofit upgrade the switchgear must be de-
energized. Please de-energize the switchgear by operating the 
switches to disconnected position. 

 

Check that all mechanism springs are discharged. If in doubt, 
close and open the switch. 

 

 
 

ABB 

ABB Technology Ltd.

 

Edition 

1.0

 

Document No. 

1VDD200010

 

Sheet No. 

2/12 

 

Summary of Contents for SafeRing













Reviews: