1SDH002031A1002 ECN000092998 Rev. B
SACE Tmax XT2
– XT4 | 147
45 - Ekip Com EtherNet/IP
TM
Ekip Com EtherNet/IP
TM
is a communication accessory that enables Ekip Touch to be integrated
into an Ethernet network with communication protocol EtherNet/IP
TM
, with supervision and
remote control functions.
The module is configured as master and from remote it is possible to
read information and Ekip Touch measurements
manage certain commands, including opening and closing actuator (MOE-E)
access to information and parameters that are not available on the display
if connected to a withdrawable circuit-breaker, check the status of inserted / extracted
NOTE: the remote open and close commands to the switch can be run only if Ekip
Touch is in Remote configuration
To map the module in its communication network, the document System Interface is available
(page 128) that lists the necessary communication and command details.
Depending on the parameters set, which are illustrated on subsequent pages, the following
module ports are used:
Port
Protocol
Notes
44818
TCP
Encapsulation Protocol (e.g.: ListIdentity, UCMM, CIP Transport
Class 3)
44818
UDP
44818 UDP Encapsulation Protocol (e.g.: ListIdentity)
2222
UDP
2222 UDP CIP Transport Class 0 or 1
68/udp
DHCP Client
DHCP client enables alternatively to
static address = On
To connect
Ekip Com EtherNet/IP
to Ekip Touch, the
Ekip Cartridge
(page 129) and
Ekip Supply
(page 130) accessories are required.
Safety
As the module enables the actuator to be controlled that is connected to Ekip Touch and enables
unit data to be accessed, it can be connected only to networks meeting all the necessary security
and unauthorized-access prevention requirements (e.g. the control system network of a plant).
IMPORTANT:
It is customer's sole responsibility to provide and continuously ensure a
secure connection between the module and customer network or any other
network (as the case may be); customer shall establish and maintain any
appropriate measures (such as but not limited to the installation of firewalls,
application of authentication measures, encryption of data, installation of
anti-virus programs, etc) to protect the product, the network, its system and
the interface against any kind of security breaches, unauthorized access,
interference, intrusion, leakage and/or theft of data or information.
ABB Ltd and its affiliates are not liable for damages and/or losses related to
such security breaches,any unauthorized access, interference, intrusion,
leakage and/or theft of data or information.
The module cannot be connected directly to the Internet; connect only to
dedicated Ethernet networks, with EtherNet/IP
TM
communication protocol
Summary of Contents for SACE Tmax XT2
