ABB SACE Tmax XT2 User Manual Download

Page: 129 / 207

1SDH002031A1002 ECN000092998 Rev. B

SACE Tmax XT2

– XT4 | 129

38 - Ekip Cartridge

Ekip Cartridge

is an external accessory that can be installed on a standard 35 mm DIN rail (DIN

EN 50022 type TS 35x15 mm), which allows other external accessories to connect to Ekip Touch:



All cartridge modules (e.g.

Ekip Supply

Ekip Com

, etc)



engaged/disengaged signal contact, in case of a CB in a detachable configuration

Models

Two different models are available that allow two or four modules to be connected respectively.

IMPORTANT: one module must always be Ekip Supply

Connections

Ekip Cartridge

has two terminal blocks:

Figure 30

Connector

Description

Terminal for connecting the engaged/disengaged status contact

NOTE: by default Ekip Cartridge is supplied with a jumper on the terminal
block

To use the engaged/disengaged status signal, remove the jumper from the
connector and connect the cables coming from the fixed part of the CB

Terminal for the connection of

Ekip Cartridge

to Ekip Touch:

Pin

Description

Power output for Ekip Touch (+24V DC)

Power output for Ekip Touch (-24V DC)

CAN bus

Access to all external connections are available on the respective modules, on the top side of

Ekip Cartridge

Assembly

To connect the module to Ekip Touch see the instruction sheets 1SDH002009A1503.

Summary of Contents for SACE Tmax XT2
















































































































































































































Search results

Summary of Contents for SACE Tmax XT2

Reviews:

Related manuals for SACE Tmax XT2

Brands by name

Popular brands

ABB SACE Tmax XT2, User Manual

Search results

Summary of Contents for SACE Tmax XT2

Reviews:

Related manuals for SACE Tmax XT2

Brands by name

Popular brands