ABB Sace Tmax XT XT5 THERMOMAGNETIC Disassembly Instructions Manual Download Page 4 | Manualshive

Page: 4 / 28

ABB Sace Tmax XT XT5 THERMOMAGNETIC Disassembly Instructions Manual Download Page 4

4

INSTRUCTION HANDBOOK

If disassembled parts require a separate treatment a specific indication is provided inside each phase
with reason why for the separate treatment (see Chapter 6).

Description

Position inside circuit breaker

Quantity

Cap kits

In correspondence of circuit breaker connection terminals

6

UVR rod

Mounted on the breaking part cover

1

Test lever

Mounted on the breaking part cover

1

Left hand lever adapter

Mounted on the breaking part cover

1

RC lever release

Mounted on the breaking part cover

1

RC lever support

Mounted on the breaking part cover

1

Right hand open/close AUX adapter

Mounted on the breaking part cover

1

Toggle extention

Mounted on the toggle

1

Toggle protection

Mounted on the toggle

1

Operating mechanism

Mounted on the central pole

1

Plugs

Mounted on the trip unit

3

Trimmers

Mounted on the trip unit

2

Tripping rod

Mounted on the trip unit

1

Rod

Mounted on the trip unit

1

6. DISASSEMBLY PROCESS

Circuit breakers disassembly process is constituted by a sequence of operations to be performed on
products after their dismounting from original installation. For each phase following information are
provided:

•  Part/parts to be disassembled (title of the phase)
•  Tools to be used
•  Description of actions to be performed
•  Pictures showing actions to be performed
•  List, quantity and picture of disassembled parts with an indication about separate treatment (when

applicable)

• In case of potential hazards signal below is reported

5. SEPARATE TREATMENT

Table below lists parts requiring a separate treatment adding information about part location inside
circuit breakers and related quantity.

«
...
2
3
4
5
6
...
»

Summary of Contents for Sace Tmax XT XT5 THERMOMAGNETIC





























Reviews:

No comments