manualshive.com logo in svg

ABB REJ601, Product Manual, Page: 15 / 24

Share
Download
ABB REJ601 Product Manual Download Page 15

Feeder protection and control / Feeder protection 

1MDB07221-YN 

REF601 / REJ601 

 

Product version: 2.2FP2 

Issued: 2017-05-09 

 

Revision: A 

 

15 

ABB 

Table 26.

 

Low-set earth-fault protection, stage Io> / 51N 

Parameter 

Value (Range) 

Setting range of pick-up current ‘Io>’ 

External earth measurement : 0.05...2.0 x In in steps 0.001, infinite 
Internal earth measurement : 0.5...2.0 x In in steps 0.001, infinite 

Operation accuracy 

External earth measurement :  ± 5.0% of set value  
External earth measurement : ± 10.0% of set value, for set value < 
0.05 
Internal earth measurement : ± 15.0% of set value 

Operate time delay (DMT) ‘t >’ 

0.04...64 s in steps of 0.01  

Minimum IDMT Trip level 

1.2 x setting of pick-up current “Io >” 

Operation time accuracy 

External earth measurement : ± 5.0% of set value or ± 30 ms  
Internal earth measurement : ± 10.0% of set value or ± 30 ms 

Operating curve type 

IEC 60255-3:  
Normal inverse, Very inverse, Extremely inverse, Long-time inverse 
ANSI C37.112:  
Moderate inverse, Normal Inverse, Very inverse, Extremely inverse 
Special curves: RI inverse 

Time multiplier setting ‘k’ 

0.02...1.6, in steps of 0.01 

Operation time accuracy 

 

IEC and ANSI characteristics  

 

RI characteristics

 

 

IEC and ANSI characteristics  

 

RI characteristics

 

 
External earth measurement : class E(5) or ± 30 ms

  

External earth measurement : class E(7.5) or 

± 

30 ms 

Internal earth measurement : 

± 

5.0% of set value or 

± 

30 ms 

Internal earth measurement : 

± 

10.0% of set value or 

± 

30 ms

 

Reset ratio 

IDMT : 0.96 and DT : 0.98 

 

Table 27.

 

High- set earth-fault protection, stage Io>> / 50N 

Parameter 

Value (Range) 

Setting range of pick-up current ‘Io >>’ 

External earth measurement : 0.05...12.5 x In in steps 0.001, infinite 
Internal earth measurement : 0.5...12.5 x In in steps 0.001, infinite 

Operation accuracy 

External earth measurement : ± 5.0% of set value 
Internal earth measurement : ± 15.0% of set value 

Operation mode 

Definite time, Instantaneous 

Operate time delay (DMT) ‘to >>’ 

0.04...64 s in steps of 0.01 

Operation time accuracy 

External earth measurement : ± 5.0% of set value or ± 30 ms 
Internal earth measurement : ± 10.0% of set value or ± 30 ms 

Reset ratio 

0.98 

 

 

Summary of Contents for REJ601

























Reviews:

No comments