manualshive.com logo in svg

ABB RBIP-01, User Manual

Share
Download
ABB RBIP-01 User Manual Download Page 5

Safety instructions

5

Safety instructions 

Overview

This chapter states the general safety instructions that must be followed when 
installing and operating the RBIP-01 BACnet/IP Router Module.

The material in this chapter must be studied before attempting any work on, or with, 
the unit.

In addition to the safety instructions given below, read the complete safety 
instructions of the specific drive you are working on.

General safety instructions

WARNING!

 All electrical installation and maintenance work on the drive should be 

carried out by qualified electricians. The drive and adjoining equipment must be 
properly earthed.

Do not attempt any work on a powered drive. After switching off the mains, always 
allow the intermediate circuit capacitors to discharge for 5 minutes before working on 
the frequency converter, the motor or the motor cable. It is good practice to check 
(with a voltage indicating instrument) that the drive is in fact discharged before 
beginning work.

The motor cable terminals of the drive are at a dangerously high voltage when mains 
power is applied, regardless of motor operation.

There can be dangerous voltages inside the drive from external control circuits even 
when the drive mains power is shut off. Exercise appropriate care when working on 
the unit. Neglecting these instructions can cause physical injury or death.

Summary of Contents for RBIP-01



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands