manualshive.com logo in svg

ABB OmniCore V400XT, Product Manual


Share
Download
background image

Detailed working procedure

Note

Action

•

If the cable is damaged, re-
place to a new cable and go
to step

8

.

•

If the cable is not connected,
repair the connection and
go to step

8

.

•

If the cable is ok, go to the
next step.

Check that the floor cable is connected from the
manipulator to the motor connector X1.
Visually inspect the cable for damage or extensive
bending marks.

Tip

For more details, see

Circuit diagram - OmniCore

V400XT

.

1

If it is not green, see

Troubleshooting the power unit on
page 381

.

Check the LED Module Status on the power unit
A1. The LED should be solid green.

2

Check the LEDs on the main computer, power
distribution board DSQC1085.

3

All LEDs should be solid green.

Use a multimeter and insulating
gloves.

•

If there is no power, repair
the connection and go to
step

8

.

•

If it is ok, go to the next
step.

Measure the power on T4.X13/X14.

Tip

For more details, see

Circuit diagram - OmniCore

V400XT

.

4

•

If it is not, repair the connec-
tion and go to step

8

.

•

If it is ok, go to the next
step.

Check that the connection from the main drive
unit to the motor connector is ok:

•

T4.X15 - X1.

5

•

If it is not, repair the connec-
tion and go to step

8

.

•

If it is ok, go to the next
step.

Check that the connection from the main drive
unit to the power unit is ok:

•

T4.X13 - A1.X11

6

•

If it is not working properly,
the brake release board on
the manipulator might be
broken. Contact your local
ABB for more information.

•

If the brakes work normally,
troubleshoot the main com-
puter, the robot signal ex-
change proxy, and the
power unit, one by one. If
needed, replace faulty units.
Go to step

8

.

Try jogging the robot.

7

For more details on how to release
the brakes, see the robot's product
manual.

•

If it is not ok, contact your
local ABB.

Check that the brake release function is ok.

8

Product manual - OmniCore V400XT

355

3HAC081697-001 Revision: A

© Copyright 2022-2023 ABB. All rights reserved.

7 Troubleshooting

7.2.4 Problem releasing the robot brakes

Continued

Summary of Contents for OmniCore V400XT



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniCore V400XT

OHBOT v2.1 Manual preview
v2.1
Brand: OHBOT Pages: 25
Samsung VR30T80 Series User Manual preview
VR30T80 Series
Brand: Samsung Pages: 46
OCCO S Operator'S Manual preview
S
Brand: OCCO Pages: 62
IAI Intelligent Actuator IX Series Operation Manual preview
Intelligent Actuator IX Series
Brand: IAI Pages: 76
YASKAWA MOTOMAN-MA1900 Instructions Manual preview
MOTOMAN-MA1900
Brand: YASKAWA Pages: 29
Parallax Boe-Bot Student Manual preview
Boe-Bot
Brand: Parallax Pages: 360
Yujin Robot iCLEBO Kobuki User Manual preview
iCLEBO Kobuki
Brand: Yujin Robot Pages: 24
White Box Robotics PC-Bot 914 Quick Start Manual preview
PC-Bot 914
Brand: White Box Robotics Pages: 56
Inex IOIO-BOT Manual preview
IOIO-BOT
Brand: Inex Pages: 56
Kuka KR 30-2 Manual preview
KR 30-2
Brand: Kuka Pages: 85
Kuka KR 300-2 PA Assembly Instructions Manual preview
KR 300-2 PA
Brand: Kuka Pages: 125
Chengdu Hangfa Hydraulic Engineering Co., Ltd Compass Q2 User Manual preview
Compass Q2
Brand: Chengdu Hangfa Hydraulic Engineering Co., Ltd Pages: 23

Brands by name

Popular brands

Load more brands