ABB OmniCore V250XT Product Manual Download Page 92

Page: 92 / 456

3.5.8 Descriptions for connectors

Robot signal exchange proxy mating connectors

xx1900002449

CAUTION

Safety functions must be verified before use. Safety functions must be tested
regularly.

Connector X14

Description

Customer Safety Interface: Automatic Stop/General Stop
and external Emergency Stop

Connection

Weidmüller B2CF 3.50/16/180F

Type

B2CF 3.50/16/180F SN OR BX 2*8 pins

3HAC064736-001

Article number

The connector X14 allows for connecting

protective stop

and

emergency stop

devices.

The input for protective stop can either be configured as

Automatic Stop

(AS) or

General Stop

(GS).

Automatic Stop

is only operational in automatic mode.

General

Stop

is operational in both manual mode and automatic mode. See

Protective stop

and emergency stop on page 20

The default configuration for the protective stop function is

Automatic Stop

(AS).

That is, active in automatic mode only.

Changes to the default configuration for the protective stop function, that is from

Automatic Stop

(automatic mode) to

General Stop

(both manual and automatic

mode), are made in the tool RobotStudio. See

Configuring robot stopping functions

on page 105

. More information is also available in

Operating manual - RobotStudio

and

Application manual - Functional safety and SafeMove

External emergency stop devices can for example be required in the following
cases:

•

FlexPendant is detached.

Continues on next page

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

3 Installation and commissioning

3.5.8 Descriptions for connectors

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Brands by name

Popular brands