ABB OmniCore V250XT Product Manual Download

Page: 105 / 456

3.5.9 Configuring robot stopping functions

Introduction

The robot stopping functions, protective and emergency stop are configured using
the

Visual SafeMove

functionality in RobotStudio.

The protective stop function can be configured to be either an

Automatic Stop

(AS)

or a

General Stop

(GS). When the protective stop function is configured as

General

Stop

(GS), the activation of the protective stop device will initiate the protective

stop in any operating mode. When the protective stop function is configured as

Automatic Stop

(AS), the activation of the protective stop device will initiate the

protective stop in automatic mode only.

Note

It is not possible to configure both

Automatic Stop

and

General Stop

on the

OmniCore V250XT without the use of a safe fieldbus.

Note

The dedicated discrete safety input to activate the protective stop function can
be configured as either

Automatic Stop

(AS) or

General Stop

(GS). For

simultaneous use of AS and GS, support for a safety protocol is required. See
option SafeMove.

For more information about safety configurations, see

Application

manual - Functional safety and SafeMove

Configure the robot stopping functions in Visual SafeMove

WARNING

The new settings must be verified by test before the robot is used.

Continues on next page

Product manual - OmniCore V250XT

105

3HAC073447-001 Revision: B

3 Installation and commissioning

3.5.9 Configuring robot stopping functions

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands