manualshive.com logo in svg

ABB OmniCore S Series, Operating Manual

The ABB OmniCore S Series is an advanced automation solution designed to streamline industrial processes. Boost productivity with our comprehensive Operating manual, available for free download at manualshive.com. Access this essential manual to unlock the full potential of your OmniCore S and optimize your operations.

Share
Download
background image

Note

The RAPID function

IsBrakeCheckActive

can be used to check if

BrakeCheck

is active.

Interrupt the brake check

It is not recommended, but it is possible to stop the execution while running a
brake check.

If the brake check is interrupted, it will be resumed when the program execution
starts again. The brake check can be resumed up to 3 times.

Brake maintenance

Brake maintenance

is a feature in the brake check functionality.

The

BrakeCheck

routine automatically detects if maintenance of the mechanical

brakes is needed and activates the

Brake maintenance

functionality during

execution.

Brake maintenance

applies the brake and turns the motor shaft 1 radian

five times, which gives a movement of the robot arm of less than 1 degree.

There are event logs that tell if

Brake maintenance

is needed, and if it has been

run.

For more information see parameter

Brake Maintenance

, type

General Rapid

, topic

Controller

, in

Technical reference manual - System parameters

.

Event logs

When

BrakeCheck

is executed, the following event logs will be shown:

Title

Event log

Brake Check Done

10272

Brake Check Started

10273

If there is a problem with one or several mechanical brakes, an event log that is
describing which mechanical unit and which axis that has bad brakes will be shown:

Title

Event log

Brake Performance Warning

37234

Brake Performance Error

37235

Brake check on additional axes

To be able to run brake check on additional axes, the parameter

Max Static Arm

Torque

(in topic

Motion

and type

Brake

) needs to be calculated for the additional

axis and entered into the configuration. Brake check uses this value when testing
the brake at error-level.

The parameter should be the maximum static torque that the brake needs to
withstand when the additional axis is positioned in maximum gravity. The following
formula should be used:

Max Static Arm Torque = (M*L*g)/n

Continues on next page

176

Operating manual - OmniCore

3HAC065036-001 Revision: E

© Copyright 20192020 ABB. All rights reserved.

6 Programming and testing

6.10.7 Brake check service routine

Continued

Summary of Contents for OmniCore S Series













































































































































































































































Reviews:

No comments

Related manuals for OmniCore S Series

Samson 3296 Mounting And Operating Instructions preview
3296
Brand: Samson Pages: 100
Danfoss JS120 Technical Information preview
JS120
Brand: Danfoss Pages: 16
Radio Shack Remote Control Owner'S Manual preview
Remote Control
Brand: Radio Shack Pages: 3
H3C WX5500H series User Configuration Manual preview
WX5500H series
Brand: H3C Pages: 57
XBOX 360 Quick Manual preview
360
Brand: XBOX Pages: 2
Parker 890 Series Quick Start Manual preview
890 Series
Brand: Parker Pages: 30
VAT 110 Series Installation, Operating, & Maintenance Instructions preview
110 Series
Brand: VAT Pages: 22
GE Evolution Series E9000 User Manual preview
Evolution Series E9000
Brand: GE Pages: 44
GE PACSystems RX7i Cpu Programmer'S Reference Manual preview
PACSystems RX7i
Brand: GE Pages: 469
GE GuardSwitch 300 Series Instructions preview
GuardSwitch 300 Series
Brand: GE Pages: 2
GE GuardSwitch 300 Series Instruction preview
GuardSwitch 300 Series
Brand: GE Pages: 2
GE Masoneilan VariPak 28001 Instruction Manual preview
Masoneilan VariPak 28001
Brand: GE Pages: 24
D+H RZN 4503-T Instructions For Use Manual preview
RZN 4503-T
Brand: D+H Pages: 14
Danfoss EKC 316A Reference Manual preview
EKC 316A
Brand: Danfoss Pages: 16
Danfoss ASV-P Installation Manual preview
ASV-P
Brand: Danfoss Pages: 20
Daktronics All Sport 5000 Operation Instructions preview
All Sport 5000
Brand: Daktronics Pages: 5
Daikin BRC2E52C7 Quick Reference preview
BRC2E52C7
Brand: Daikin Pages: 12
Raypak RayTemp Installation & Operating Instructions Manual preview
RayTemp
Brand: Raypak Pages: 24

Brands by name

Popular brands

Load more brands