ABB LevelMaster 7100, User Manual, Page: 98 / 100

LevelMaster 7100 User manual 2105835 Rev AA | 88
IMPORTANT NOTES: If no port is set to LevelMaster protocol, the following message will appear: “No port
protocol set to LevelMaster Interface.” To verify communication configuration or correct port parameters, see
section 6.2,
Set up general and communications parameters.
The characters at the Character Return Checks (CRC) are used to ensure good communications. These start
with “C” and can be ignored.
11. Capture or take a snapshot of the values displayed if needed.
12. To exit terminal mode and return to the PCCU32 Entry screen, press the ESC key.
A.2.1 Example 1: Obtaining the content of the EPROM memory
The following example shows how to use one of the commands to obtain the contents of the EPROM memory.
To display the values:
1. At the terminal mode screen prompt, type the command to obtain memory values: LM>U03ED0.
2. Observe the values displayed:
003 003 008 003 003 100 001 025 001 010 044 000 079 000 010 007
002 083 001 001 083 000 006 001 000 001 010 010 005 129 002 091
000 012 002 204 000 079 003 050 246 004 040 246 004 058 000 200
246 009 199 255 254 077 240 011 248 000 000 000 000 000 006 200
128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128
128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128
128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128
128 128 128 128 128 128 128 128 128 128 128 128 128 128 128 128
255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
255 255 255 255 255 255 255 255 255 255 255 255 255 255 255 255
A.2.2 Example 2: Obtaining raw data values
The following example shows how to use one of the commands to obtain raw data values.
To display the values:
1. At the terminal mode screen prompt, type the command to obtain memory values: LM> U???
2. Observe the values displayed:
V0=+00006 V1=-00708 V2=-00085 V3=-00802 AVG
V0=-06447 V1=+05155 V2=-06952 V3=-07166 PC00548 F0
V0=+07765 V1=+01656 V2=+04361 V3=+08909 PC00548 F1
V0=-06447 V1=+05155 V2=-06952 V3=-07166 5 7 S00557 L02285 021 F0
V0=+07765 V1=+01656 V2=+04361 V3=+08909 2 3 S00245 L01113 010 F1
R=10727 T1=10950 T2=10762 T3=10733 T4=10722 T5=10731