ABB i-bus VC/S 4 1 Series Product Manual Download Page 96

Page: 96 / 199

ABB i-bus® KNX

PARAMETERS

7.4.71

Manual operation

This parameter is used to enable or block manual operation of the device.

Option

Enabled

The operating states

Manual operation

and

KNX operation

can be switched via the

Manual operation

button or via group object

Enable/block manual operation

. The device can be operated using the

membrane keypad.

The following dependent parameters are shown:
•

Automatic reset from manual operation to KNX operation

The following dependent group objects are displayed:
•

Status Manual operation

•

Enable/block manual operation

Blocked

Manual operation of the device is blocked.

Prerequisites for visibility

• Product variant:

– VC/S 4.2.1

• The parameter is in the parameter window

Manual operation

7.4.72

Enable manual valve override

This parameter is used to define whether manual valve override can be enabled via a group object.

More information: → ⁠

Manual valve override, Page ⁠⁠180

Note

The value of group object

Override valve control value X

becomes active only when manual valve over-

ride has been enabled via group object

Enable/block manual valve override X

Option

Manual valve override cannot be enabled via a group object.

Yes

Manual valve override can be enabled.

The following dependent group objects are displayed:
•

Enable/block manual valve override X

•

Override valve control value X

Prerequisites for visibility

\ Parameter

\ Options

Thermoelectric (PWM)

Open/close signal

• The parameter is in the parameter window

Channel X

\ parameter window

Valve output X

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Summary of Contents for i-bus VC/S 4 1 Series








































































































































































































Search results

Summary of Contents for i-bus VC/S 4 1 Series

Reviews:

ABB i-bus VC/S 4 1 Series, Product Manual, Page: 96 / 199

Search results

Summary of Contents for i-bus VC/S 4 1 Series

Reviews: