manualshive.com logo in svg

ABB HT613213, Operation Manual, Page: 57 / 148

Share
Download
ABB HT613213 Operation Manual Download Page 57

Operation Manual / A170-M.. - A175-M..

7 Periodic maintenance / 7.2 Cleaning the filter silencer

© Copyright 2022 ABB. All rights reserved.

HZTL4033_EN

Rev.K

January 2022

Cleaning the absorption segments (81136)

u

Pull out and bend up the sheet-metal coverings (81137), and remove the absorption seg-
ments (81136).

u

Clean the absorption segments.
When cleaning, note that the absorption segments may only be cleaned lightly with pres-
surized air, a soft brush or a moist cleaning cloth.

u

Have any heavily contaminated absorption segments replaced by an ABB Turbocharging
Service Station.

Fitting the filter silencer

u

Insert the absorption segments (81136) into the sheet-metal coverings (81137).

u

Bend the sheet-metal coverings (81137) back to their original shape and insert into the
slotted guides in the filter silencer body (81135).

u

If the cleaning container is present on the filter silencer: Reinstall the water injection pipe.

Page 

55

 / 

146

Summary of Contents for HT613213





















































































































































Reviews:

No comments