ABB HT611658 Operation Manual Download

Page: 97 / 148

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.8 Installing the nozzle ring

HZTL4033_EN

Rev.K

January 2022

Fig. 51: Installing nozzle ring 2

Product

Size

Tightening torque [Nm]

A170-M

M10

A175-M

M10

Table 37: Tightening torque (56014)

6. Loosen nuts (61037) and remove guide plate (90328).

7. Loosen screws (90339) and remove retaining plate (90338) with guide rod (90336).

8. Coat the threads of screws (56014) and the contact surface between screw and locking

washer with high-temperature grease.

9. Fit the nozzle ring (56001) on the gas inlet casing (51001) using the screws (56014) and

locking washers (56015).

10. Bend over locking washers (56015).

Page

146

Summary of Contents for HT611658



















































































































































Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands

ABB HT611658, Operation Manual

Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands