ABB HT608501 Operation Manual Download Page 58

Page: 58 / 148

Operation Manual / A170-M.. - A175-M..

7 Periodic maintenance / 7.3 Cleaning the slotted diffuser

HZTL4033_EN

Rev.I

November 2021

Tighten screws (81272) alternately and evenly. Observe tightening torque

Screw

Tightening torque [Nm]

81272

Table 15: Tightening torque (81272)

Fit the lock nuts (81273) on the screw (81272). Observe tightening torque.

Lock nut

Tightening torque [Nm]

81273

Table 16: Tightening torque (81273)

If present: Fit the filter ring (81265)

(see Fig. 26: Cleaning the filter silencer

→

54)

7.3

Cleaning the slotted diffuser

Remove the diffuser (see

Removing the compressor casing

→

Fig. 28: Cleaning the slotted diffuser

Clean the diffuser slots (S).
When cleaning, please note that this should only take place using lightly pressurized air, a
brush and a moist cleaning cloth.

Have any heavily contaminated or damaged diffusers replaced by an ABB Turbocharging
Service Station.

Page

146

Summary of Contents for HT608501



















































































































































Search results

Summary of Contents for HT608501

Reviews:

Related manuals for HT608501

Brands by name

Popular brands

ABB HT608501, Operation Manual

Search results

Summary of Contents for HT608501

Reviews:

Related manuals for HT608501

Brands by name

Popular brands