ABB HT601685 Operation Manual Download Page 31

Page: 31 / 124

Operation Manual / 4 Product description / A130-H.. - A140-H

Table of contents

HZTL4030_EN

Rev.F

February 2020

Product description

Introduction............................................................................................................ 3

1.1

Essential information.................................................................................................... 3

1.2

Registered trademarks ................................................................................................. 3

1.3

Related documents........................................................................................................ 3

1.4

Layout and function of the turbocharger ................................................................ 4

1.5

Warning plates on the turbocharger......................................................................... 6

1.6

Locations of the rating plates..................................................................................... 7

Removing and Installing........................................................................................ 8

2.1

Weight and transportation of the turbocharger.................................................... 8

2.2

Removing the turbocharger........................................................................................ 9

2.3

Installing the turbocharger ........................................................................................ 13

Commissioning .................................................................................................... 20

3.1

Oil supply ...................................................................................................................... 20

3.2

Inspection procedures ................................................................................................ 22

3.3

Commissioning after taking out of operation...................................................... 24

Monitoring operation .......................................................................................... 25

4.1

Oil pressure, oil temperature.................................................................................... 25

4.2

Exhaust gas temperature before turbine ............................................................... 27

4.3

Turbocharger speed ................................................................................................... 28

Operation and service ......................................................................................... 31

5.1

Noise emission ............................................................................................................. 31

5.2

Service work ................................................................................................................. 33

5.3

Expected replacement intervals ............................................................................... 37

5.4

Stopping the engine................................................................................................... 39

Periodic maintenance work ................................................................................ 40

6.1

Foreword to maintenance......................................................................................... 40

6.2

Cleaning components mechanically ........................................................................ 41

Eliminating malfunctions.................................................................................... 51

7.1

Malfunctions when starting....................................................................................... 51

7.2

Malfunctions during operation ................................................................................ 52

7.3

Turbocharger is surging ............................................................................................ 55

7.4

Malfunctions when stopping.................................................................................... 56

7.5

Speed measurement system ..................................................................................... 57

Dismantling and fitting....................................................................................... 58

8.1

Introduction ................................................................................................................. 58

Summary of Contents for HT601685





























































































































Search results

Summary of Contents for HT601685

Reviews:

Brands by name

Popular brands

ABB HT601685, Operation Manual

Search results

Summary of Contents for HT601685

Reviews:

Brands by name

Popular brands