ABB HT597879 Operation Manual Download Page 42

Page: 42 / 124

Operation Manual / 4 Product description / A130-H.. - A140-H

2 Removing and Installing / 2.2 Removing the turbocharger

HZTL4030_EN

Rev.F

February 2020

2.2.3

Putting down the turbocharger

WARNING

Risk of tipping

If the turbocharger is not positioned stably, it may tip over. This can result in
serious personal injury.

Place the turbocharger on a clean, level support.

Secure the turbocharger to prevent it from tipping over by using wooden
beams and wedges and by taking the centre of gravity into account.

Fig. 8: Putting down the turbocharger

Remove turbocharger from engine support, set it down properly in an appropriate place
and secure it.

Close or cover the openings of the turbocharger and support.

Page

Summary of Contents for HT597879





























































































































Search results

Summary of Contents for HT597879

Reviews:

Related manuals for HT597879

Brands by name

Popular brands

ABB HT597879, Operation Manual

Search results

Summary of Contents for HT597879

Reviews:

Related manuals for HT597879

Brands by name

Popular brands