ABB HT595115 Operation Manual Download

Page: 36 / 124

Operation Manual / 4 Product description / A130-H.. - A140-H

1 Introduction / 1.5 Warning plates on the turbocharger

HZTL4030_EN

Rev.F

February 2020

1.5

Warning plates on the turbocharger

Warning plates are affixed at the following locations:

Fig. 3: Warning plate locations

If warning plates are not present in the designated locations or not readable, proceed as fol-
lows:

Order new warning plates from ABB Turbocharging Service Stations.

Remove any warning plates that have become unreadable.

Clean and degrease the areas designated for the warning plates.

Fit new warning plates and remove protective sheets.

Turbochargers supplied to the enginebuilder without insulation must be equipped later with
warning plates on the insulation. This is the responsibility of the enginebuilder.

Page

Summary of Contents for HT595115





























































































































Search results

Summary of Contents for HT595115

Reviews:

Related manuals for HT595115

Brands by name

Popular brands

ABB HT595115, Operation Manual

Search results

Summary of Contents for HT595115

Reviews:

Related manuals for HT595115

Brands by name

Popular brands