ABB HT590070 Operation Manual Download | Manualshive

Page: 39 / 124

background image

Operation Manual / 4 Product description / A130-H.. - A140-H

2 Removing and Installing / 2.2 Removing the turbocharger

© Copyright 2018 ABB. All rights reserved.

HZTL4030_EN

Revision E

September 2018

2.2

Removing the turbocharger

u

Disconnect all pipes according to the instructions of the enginebuilder.

u

If present: Loosen and remove the compressor wheel cooling connection. Close the com-
pressor wheel cooling opening with a screw plug (01).

Fig. 6: Removing the turbocharger

A

Position of expansion sleeves

B

Clamping nut

C

Standard nut

u

Apply penetrating oil to thread of stud (02) and nut and let it work in.

u

If present: Disconnect the plug to the speed sensor (86505) and secure the rolled-up
cable on the turbocharger. This protects the plug from being crushed.

u

If present: Detach the support (61301) from the engine support.

Depending on the bracket version (04), two positioning pins (05) can be used for positioning
and safeguarding against wrong fitting of the turbocharger. Therefore the turbocharger
must always be removed from and installed on the bracket vertically.

The gas outlet casing (61001) can remain fitted in the exhaust gas pipe if the locking nuts
are accessible. Otherwise the complete turbocharger unit including gas outlet casing must
be removed.

Page

9

/

93

«
...
37
38
39
40
41
...
»

Summary of Contents for HT590070





























































































































Reviews:

No comments

Related manuals for HT590070

DVCPRO P2 Series

Brand: Panasonic Pages: 32

Brand: JB Systems Pages: 7

Brand: 3B SCIENTIFIC PHYSICS Pages: 36

Brand: 3A HEALTH CARE Pages: 16

Short/cut 2000 Audio Editor

Brand: 360 Systems Pages: 4

Brand: Badger Meter Pages: 16

Brand: Haag-Streit Pages: 16

Brand: IDEAL Pages: 12

Brand: Kamikaze Pages: 112

Brand: KAM Pages: 2

Brand: Landoll Pages: 70

Brand: Landice Pages: 19

Brand: Landice Pages: 7

Brand: NanoVibronix Pages: 2

Brand: NanoVibronix Pages: 32

Shapes Hexagons

Brand: Nanoleaf Pages: 27

Brand: ParaBody Pages: 6

Brand: ParaBody Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands