ABB HT578726 Operation Manual Download Page 31

Page: 31 / 142

Operation Manual / 4 Product description / A130-M.. - A145-M..

Table of contents

HZTL4031_EN

Revision F

August 2017

Product description

Introduction............................................................................................................ 3

1.1

Essential information.................................................................................................... 3

1.2

Registered trademarks ................................................................................................. 3

1.3

Related documents........................................................................................................ 3

1.4

Layout and function of the turbocharger ................................................................ 4

1.5

Warning plates on the turbocharger......................................................................... 6

1.6

Locations of the rating plates..................................................................................... 7

Removing and Installing........................................................................................ 8

2.1

Turbocharger weight and transportation ............................................................... 8

2.2

Removing the turbocharger........................................................................................ 9

2.3

Installing the turbocharger ........................................................................................ 13

Commissioning .................................................................................................... 20

3.1

Oil supply ...................................................................................................................... 20

3.2

Inspection procedures ................................................................................................ 22

3.3

Commissioning after taking out of operation...................................................... 24

Monitoring operation .......................................................................................... 25

4.1

Oil pressure, oil temperature.................................................................................... 25

4.2

Exhaust gas temperature before turbine ............................................................... 27

4.3

Turbocharger speed ................................................................................................... 28

Operation and service ......................................................................................... 31

5.1

Noise emission ............................................................................................................. 31

5.2

Service work ................................................................................................................. 33

5.3

Expected replacement intervals ............................................................................... 37

5.4

Stopping the engine................................................................................................... 39

Periodic maintenance work ................................................................................ 40

6.1

Foreword to maintenance......................................................................................... 40

6.2

Cleaning the compressor during operation ........................................................... 41

6.3

Cleaning the turbine during operation................................................................... 45

6.4

Cleaning components mechanically ....................................................................... 49

Eliminating malfunctions.................................................................................... 59

7.1

Malfunctions when starting...................................................................................... 59

7.2

Malfunctions during operation ................................................................................ 60

7.3

Turbocharger is surging ............................................................................................ 63

7.4

Malfunctions when stopping.................................................................................... 64

7.5

Speed measurement system .................................................................................... 65

Summary of Contents for HT578726















































































































































Search results

Summary of Contents for HT578726

Reviews:

Brands by name

Popular brands

ABB HT578726, Operation Manual

Search results

Summary of Contents for HT578726

Reviews:

Brands by name

Popular brands