ABB HT577436 Operation Manual Download Page 31

Page: 31 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

Table of contents

HZTL4030_EN

Revision D

May 2017

Product description

Introduction............................................................................................................ 3

1.1

Essential information.................................................................................................... 3

1.2

Registered trademarks ................................................................................................. 3

1.3

Related documents........................................................................................................ 3

1.4

Layout and function of the turbocharger ................................................................ 4

1.5

Warning plates on the turbocharger......................................................................... 6

1.6

Locations of the rating plates..................................................................................... 7

Removing and Installing........................................................................................ 8

2.1

Turbocharger weight and transportation ............................................................... 8

2.2

Removing the turbocharger........................................................................................ 9

2.3

Installing the turbocharger ........................................................................................ 13

Commissioning .................................................................................................... 20

3.1

Oil supply ...................................................................................................................... 20

3.2

Inspection procedures ................................................................................................ 22

3.3

Commissioning after taking out of operation...................................................... 24

Monitoring operation .......................................................................................... 25

4.1

Oil pressure, oil temperature.................................................................................... 25

4.2

Exhaust gas temperature before turbine ............................................................... 27

4.3

Turbocharger speed ................................................................................................... 28

Operation and service ......................................................................................... 31

5.1

Noise emission ............................................................................................................. 31

5.2

Service work ................................................................................................................. 33

5.3

Expected replacement intervals ............................................................................... 37

5.4

Stopping the engine................................................................................................... 38

Periodic maintenance work ................................................................................ 39

6.1

Foreword to maintenance......................................................................................... 39

6.2

Cleaning components mechanically ....................................................................... 39

Eliminating malfunctions.................................................................................... 49

7.1

Malfunctions when starting...................................................................................... 49

7.2

Malfunctions during operation ................................................................................ 50

7.3

Turbocharger is surging ............................................................................................ 53

7.4

Malfunctions when stopping.................................................................................... 54

7.5

Speed measurement system .................................................................................... 55

Dismantling and fitting....................................................................................... 56

8.1

Introduction ................................................................................................................. 56

Summary of Contents for HT577436



























































































































Search results

Summary of Contents for HT577436

Reviews:

ABB HT577436, Operation Manual, Page: 31 / 122

Search results

Summary of Contents for HT577436

Reviews: