ABB HT566739 Operation Manual Download

Page: 31 / 128

Operation Manual / TPL67-C.. - TPL71-C..

Safety

Hazards during operation and

maintenance

2.7

Page 29

Apr

il 2016

L2488_

ion

Hazards when handling insulating materials

WARNING

Hazards due to insulating materials
Dust and fibres from insulating materials can cause damage to health

or irritations. Unsuitable, combustible insulating materials signify a fire

hazard.



Use only suitable, non-combustible insulating materials.



Ensure that the work area is well ventilated.



Avoid stirring up dust.



Use tools and processes which keep dust to a minimum.



Remove packing materials only in the work area.



Take particular care when removing old insulating materials.



Dispose of insulating materials properly and in an environmentally

compatible way in accordance with applicable local regulations.

Wear safety goggles.

Wear a respiratory mask to protect against particles.

Wear safety gloves against chemical risks.



Use only suitable, non-combustible insulating materials.



Ensure that the work area is well ventilated.



Wear suitable work clothing (safety glasses, respiratory mask).



Avoid stirring up dust.



Use tools and processes which keep dust to a minimum.



Remove packing materials only in the work area.



Take particular care when removing old insulating materials.



Dispose of insulating materials properly and in an environmentally

compatible way in accordance with applicable local regulations.

Summary of Contents for HT566739
































































































































Search results

Summary of Contents for HT566739

Reviews:

Related manuals for HT566739

Brands by name

Popular brands

ABB HT566739, Operation Manual

Search results

Summary of Contents for HT566739

Reviews:

Related manuals for HT566739

Brands by name

Popular brands