ABB H8131 P Series Product Manual Download Page 2

Page: 2 / 61

Table of contents

Product manual 2TMD041900D0015

│

Table of c onte nts

Notes on the instruction manual ............................................................................................................ 4

Safety .................................................................................................................................................. 4

Intended use ........................................................................................................................................ 4

Environment ......................................................................................................................................... 5
4.1

ABB devices .............................................................................................................................. 5

Product description ............................................................................................................................... 6
5.1

Device type ............................................................................................................................... 6

5.2

Control elements........................................................................................................................ 7

5.3

Terminal description ................................................................................................................... 8

5.4

Lock type and connection ........................................................................................................... 9

Technical data .................................................................................................................................... 10

Mounting/Installation ........................................................................................................................... 11
7.1

Requirement for the electrician ................................................................................................. 11

7.2

Mounting ................................................................................................................................. 12

7.2.1

Preparation .......................................................................................................................... 12

7.2.2

Installation height.................................................................................................................. 12

7.2.3

Installation situation .............................................................................................................. 13

7.2.4

Surface-mounted installation ................................................................................................. 14

7.2.5

Flush-mounted installation .................................................................................................... 16

7.2.6

Cavity wall installation ........................................................................................................... 17

7.2.7

Replacing the nameplate ...................................................................................................... 18

Commissioning ................................................................................................................................... 19
8.1

Configure the settings on indoor station .................................................................................... 19

8.1.1

Enter engineering mode of outdoor station ............................................................................. 19

8.1.2

Enter outdoor station through an indoor station ...................................................................... 20

8.1.3

Device type settings.............................................................................................................. 22

8.1.4

Unlock type when swiping setting .......................................................................................... 26

8.1.5

Default lock setting ............................................................................................................... 27

8.1.6

Subsidiary lock setting .......................................................................................................... 28

8.1.7

Door status detection setting ................................................................................................. 29

8.1.8

Tamper proof alarm setting ................................................................................................... 30

8.1.9

Ringtone volume setting........................................................................................................ 31

8.1.10

Button tone setting ................................................................................................................ 32

8.1.11

Voice prompts setting ........................................................................................................... 33

8.1.12

Language setting .................................................................................................................. 34

8.1.13

Lift control setting ................................................................................................................. 35

8.1.14

Anti-flicker setting ................................................................................................................. 36

8.1.15

Call forward setting ............................................................................................................... 37

8.1.16

Wiegand setting.................................................................................................................... 38

8.1.17

Push-button setting ............................................................................................................... 39

8.1.18

Time sync setting.................................................................................................................. 41

8.1.19

Compatible mode setting ...................................................................................................... 42

8.1.20

Updating the firmware ........................................................................................................... 43

Summary of Contents for H8131 P Series






























































Search results

Summary of Contents for H8131 P Series

Reviews:

Related manuals for H8131 P Series

Brands by name

Popular brands

ABB H8131 P Series, Product Manual

Search results

Summary of Contents for H8131 P Series

Reviews:

Related manuals for H8131 P Series

Brands by name

Popular brands