ABB FBIP-21 BACnet/IP User Manual Download

Page: 63 / 74

Appendix C - FBIP-21 configuration web
pages

Contents of this chapter

This chapter presents the FBIP-21 configuration web pages.

Note: ABB recommends to disable the web pages after the commissioning to reduce
cyber security risks. See the

Service configuration page (page 66)

Browser requirements

Any web browser can be used.

Compatibility

The web pages support all drives compatible with the FBIP-21 adapter module.

For the compatibility table, see section

Compatibility (page 11)

Logging in

Open a web browser and type the IP address of the adapter module in the address
field. The IP address is visible in the FBIP-21 configuration parameters, group A,
parameter 5...8.

Example: https://192.168.0.100/

Appendix C - FBIP-21 configuration web pages 63

Summary of Contents for FBIP-21 BACnet/IP










































































Search results

Summary of Contents for FBIP-21 BACnet/IP

Reviews:

Related manuals for FBIP-21 BACnet/IP

Brands by name

Popular brands

ABB FBIP-21 BACnet/IP, User Manual

Search results

Summary of Contents for FBIP-21 BACnet/IP

Reviews:

Related manuals for FBIP-21 BACnet/IP

Brands by name

Popular brands