manualshive.com logo in svg

ABB FBIP-21 BACnet/IP, User Manual

Share
Download
ABB FBIP-21 BACnet/IP User Manual Download Page 11

Introduction to the manual

Contents of this chapter

This chapter introduces this manual.

Applicability

This manual applies to the FBIP-21 BACnet/IP adapter module, SW version 2.0 and
later.

Compatibility

The FBIP-21 fieldbus adapter module is compatible with the following drives and
protocols:

ACH480, ACH580, ACH580 E-Clipse bypass

Drives

• Ethernet standards IEEE 802.3 and IEEE 802.3u
• All BACnet/IP clients that support protocol version 1, revision 14.

Protocols

Target audience

This manual is intended for people who plan the installation, install, start up, use and
service the module. Before you do work on the module, read this manual and the
applicable drive manual that contains the hardware and safety information for the
product in question. You are expected to know the fundamentals of electricity, wiring,
electrical components, and electrical schematic symbols.

2

Introduction to the manual 11

Summary of Contents for FBIP-21 BACnet/IP











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands