background image

8

7.4 Service

When meter is in for service there can be a
necessity to change the parameter setting within the
meter. Some parameters can be changed in the
F4HC meter without the “Service program” version
“FxHC”. Following service procedure is
recommended:

1.

 

Brake the seals, set meter into

 “Service

mode”, 

see “Service mode” under display and

“Seals” for more information.

2.

 

Make the changes

see below for explanation

and see "Display, Service mode” for display
sequence.

3.

 

Exit 

service

 mode

, see 1,

4.

 

Replace the broken seals

.

7.4.0 Time

Service sequence, value number : 

”00”

The time is shown in “HHMM” where the two
digits “HH” is hour with two digits, and “MM” is
minutes with two digits.

7.4.1 Date

Service sequence, value number : 

”01”

The time format is “YYMMDD”, where,
“ YY”=Yeas, “MM”=Months and “DD”=Days.

7.4.4 Account days

The F4 have to account days at service sequence, value
number :
 

”04”,

 Account day 1

 

“05”,

 Account day 2.

The format is ”MMDD”, ”MM”= Months, ”DD”=
Days. If the ”MMDD” is set to ”0000” the meter
will not store account days.

7.4.6 Communication address
     

(primary address)

The primary communication address can be
changed in display sequence 

”06”.

 The communi-

cation address can be set with three (3) digits, with
the value 0-250.

Example

, address 5 on display: 0005.

7.4.7 Resetting stored error time

Service sequence, value number : 

”07”

 will reset

the stored error time. By changing the value to “0”
will reset the stored error time.

7.4.8 Placement of flow sensor
placing

Service sequence, value number : 

”08” 

is for

setting placement of flow sensor. Format 1 or 0.
Where:

1. = Flow sensor installed in return (cold) end of pipe
2. = Flow sensor installed in forward (hot) end of pipe.

7.4.9 Recommended date for battery
replacement

Service sequence, value number : 

”09”

 displays

recommended date for battery replacement. The
format is “ YYMMDD”. Where “ YY” = Years,
“MM”=Months, “DD”= Days.

7.3.A Return to normal mode

Service sequence, value number : 

”0A” 

displays

return to normal mode. When value is set to 1 the
meter exits the service mode when leaving “0A”
sequence.

Summary of Contents for F4HC











Reviews: