ABB EasyLine EL3020 Instructions For Installation Start-Up And Operation Download Page 56

Page: 56 / 136

EasyLine EL3000 Series Commissioning Instructions

Gas Connections for Limas23 with Magnos206 (Model EL3020)

Limas23: Gas Connections

Sample gas inlet

Sample gas outlet

Design:

Screwed fittings with hose nozzles (stainless steel 1.4305/SAE 303) for hoses
with 4 mm inner diameter (supplied)

Note:

The pressure sensor is connected internally in the outlet of the sample cell.

Magnos206: Gas Connections

Sample gas inlet

Sample gas outlet

Design:

1/8 NPT female thread (stainless steel 1.4305/SAE 303)
Connection of flexible tubes: straight screwed fittings (PP) with nozzles for flexible
tubes with inside diameter = 4 mm (supplied)
Connection of pipelines: Threaded connections (not supplied)

Note:

The sample gas inlet of the Limas23 is connected ex works to the sample gas
inlet of the Magnos206.

Summary of Contents for EasyLine EL3020









































































































































Search results

Summary of Contents for EasyLine EL3020

Reviews:

Related manuals for EasyLine EL3020

Brands by name

Popular brands

ABB EasyLine EL3020, Instructions For Installation Start-Up And Operation

Search results

Summary of Contents for EasyLine EL3020

Reviews:

Related manuals for EasyLine EL3020

Brands by name

Popular brands