ABB DPA UPScale ST40 User Manual Download Page 50

Page: 50 / 129

Modifications reserved

Page 50/79

6.4.2

JD1 / RS232 smart port computer interface

The Computer Interface JD1 (4) located on the distribution part is an intelligent RS232 serial port that

allows the UPS to be connected to a computer. The connector JD1 is a standard D-Type, 9-pin,
female.

The optional WAVEMON software allows the computer to monitor the mains voltage and the UPS

status continuously.
In the event of any changes, the computer terminal will display a message.

(For details see ABB’s optional monitoring package: WAVEMON).

6.4.3

USB computer interface

The Computer Interface USB (5) is located on the distribution part and is in parallel with the
intelligent RS232 serial port JD1.

The optional WAVEMON software allows the computer to monitor the mains voltage and the UPS

status continuously.

In the event of any changes, the computer terminal will display a message.

(For details see ABB’s optional monitoring package: WAVEMON).

Fig 6.4.3-1: Distribution Interfaces

JR2 / RS485

(Not used ) foreseen for RJ45 Plug

Customer interface on Phoenix terminals

= Potential free contacts

Customer inputs (detail see chapter 6.4.2 )

JD1

Smart port RS232 / sub D9/ female,

PC interface

USB

PC interface

SNMP

Slot for optional SNMP card ONLY

Modem

Slot for optional modem/ethernet card ONLY

Summary of Contents for DPA UPScale ST40




























































































































Search results

Summary of Contents for DPA UPScale ST40

Reviews:

Related manuals for DPA UPScale ST40

Brands by name

Popular brands

ABB DPA UPScale ST40, User Manual

Search results

Summary of Contents for DPA UPScale ST40

Reviews:

Related manuals for DPA UPScale ST40

Brands by name

Popular brands