ABB AV1 Operating Instructions Manual Download Page 68

Page: 68 / 126

REPAIR AND REPLACEMENT

PILOT VALVE STROKE ADJUSTMENT

8 - 8

b. If manual override is not available, disconnect (and
secure) the linkage. Plug ports 01 and 02

if necessary

Apply the supply pressure.

Apply the maximum input signal to the positioner:

•

AV11: 103.4 kPa (15.0 psig).

•

AV12:186.2 kPa (27.0 psig).

•

AV23: 20 mA.

Use the long

-inch Allen wrench

adjust the top adjustment

screw (Fig.

8-4

) appropriately until the measurement matches the

value shown in Figure

8-3

. Figure

8-3

also shows the way the mea-

surement is taken.

Apply the minimum input span to the positioner:

•

AV11: 20.7 kPa (3.0 psig).

•

AV12: 20.7 kPa (3.0 psig).

•

AV23: 4 mA.

Use the long

-inch Allen wrench to adjust the lower stroke

adjustment screw (Fig.

8-4

). Adjust the screw until the measurement

matches the value shown in Figure

8-3

Figure 8-3. Pilot Valve Measurement for Maximum Speed

⁄

STEM IS
FLUSH
WITH BODY

0.030

STEM POSITION AT

BALANCE CONDITION

STEM POSITION TOP

ADJUSTMENT SCREW

STEM POSITION LOWER

ADJUSTMENT SCREW

T00777A

Summary of Contents for AV1































































































































Search results

Summary of Contents for AV1

Reviews:

ABB AV1, Operating Instructions Manual, Page: 68 / 126

Search results

Summary of Contents for AV1

Reviews: