ABB ACx580-01-02A6-4 Service Instructions Manual Download

Page: 7 / 41

On-Site Service Instructions

Document nbr

3AXD10000303478

ABB Oy, Drives Service

ACx580-01 R0-R5

Related to material

Department

Date

Revision

Page

ESP300

13.08.2018

7 (41)

2.2.2 Frame R0 IP55, Internal cooling fan

Types:

•

ACx580-01-02A6-4

•

ACx580-01-03A3-4

•

ACx580-01-04A0-4

•

ACx580-01-05A6-4

Remove front cover

a.  Remove control panel
b.  Open mounting screw with a screwdriver
c.  Push the front cover slightly upwards and lift it off

Replace internal fan

a. Remove internal fan sledge from plastic housing
b. Assembly new internal fan+sledge combination

i. Place internal fan to sledge, ensure correct blowing direction

ii. Place FR-1 rivets through the holes and push them to bottom

c. Place internal fan sledge to plastic housing

Install components in reverse order

Summary of Contents for ACx580-01-02A6-4










































Search results

Summary of Contents for ACx580-01-02A6-4

Reviews:

Related manuals for ACx580-01-02A6-4

Brands by name

Popular brands

ABB ACx580-01-02A6-4, Service Instructions Manual

Search results

Summary of Contents for ACx580-01-02A6-4

Reviews:

Related manuals for ACx580-01-02A6-4

Brands by name

Popular brands