ABB ACx580-01-02A6-4 Service Instructions Manual Download | Manualshive

Page: 41 / 41

background image

On-Site Service Instructions

Document nbr

3AXD10000303478

ABB Oy, Drives Service

ACx580-01 R0-R5

Related to material

Department

Date

Revision

Page

ESP300

13.08.2018

F

41 (41)

© Copyright 2018 ABB Oy. All rights reserved. Specifications subject to change without notice.

4. Replacement of interface options

Optional modules such as fieldbus adapters and I/O extensions are inserted in the optional module
slot on the control unit.

ACX580 CCU control unit contains three option slots. In the table below there is described which
interface options can be used in which slot

Option modules

Install to

Fieldbus adapters (FENA, FPBA)

Slot 1

I/O extensions (CMOD)

Slot 2

Embedded fieldbus (CEIA)

Slot 3

Install the optional modules as follows:

1. Insert the module carefully into its position on the control board.
2. Fasten the fastening screws.

Note

: Proper tightening of the screws is essential for fulfilling the

EMC requirements and for proper operation of the module.

Slot 1

Slot 3

Slot 2

CCU-11 option slots

CCU-12 option slots

Slot 1

Slot 3

Slot 2

«
...
39
40
41

Summary of Contents for ACx580-01-02A6-4










































Reviews:

No comments

Related manuals for ACx580-01-02A6-4

Brand: Bartscher Pages: 22

Brand: B&K Pages: 5

Brand: B&K Pages: 28

Brand: NEC Pages: 29

Brand: Quincy lab Pages: 4

Brand: Parker Pages: 5

Brand: Bacharach Pages: 31

Brand: Bacharach Pages: 2

Brand: xsto Pages: 76

Brand: F&V Pages: 5

Brand: F Care Systems Pages: 2

Brand: ICELED Pages: 4

Brand: Facom Pages: 4

Brand: FaceLake Pages: 2

Brand: FabiaTech Pages: 2

Brand: FabiaTech Pages: 77

Brand: Water Witch Pages: 2

Brand: Falltech Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands