manualshive.com logo in svg

ABB ACS880-1604, Hardware Manual

Share
Download
ABB ACS880-1604 Hardware Manual Download Page 118

118   Maintenance

LEDs and other status indicators

This section instructs how to interpret the status indications of the ACS880-1604 DC/DC 
converter.

Warnings and faults reported by the control program are displayed on the control panel on 
the cabinet door. For further information, see the firmware manual.

The ACS-AP-x control panel has a status LED. The control panel mounting platform has 
two LEDs - a red and a green one. The DC/DC converter module (frame R8i) has three 
LEDs. For their indications, see the following table.

Location

LED

Indication

ACS-AP-x control panel 
(status LED)

Continuous green

The DC/DC converter is functioning normally.

Flickering green

Data is transferred between the PC tool and DC/DC 
converter through the USB connection of the control 
panel.

Blinking green

There is an active warning in the DC/DC converter.

Continuous red

There is an active fault in the DC/DC converter.

Control panel mounting 
platform (with the control 
panel removed)

Red

There is an active fault in the DC/DC converter.

Green

Power supply for the control board of the DC/DC 
converter is OK.

DC/DC converter module

FAULT 
(continuous red)

There is an active fault in the DC/DC converter 
module.

ENABLE / STO 
(continuous green)

The DC/DC converter module is ready for use.

ENABLE / STO 
(continuous 
yellow)

XSTO connectors are de-energized.

POWER OK 
(continuous green)

Supply voltage on the board is OK (> 21 V).

Summary of Contents for ACS880-1604































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands