ABB ACS880-04F Hardware Manual Download Page 115

Page: 115 / 172

Maintenance 115

Replacing the control panel battery

The battery is housed on the rear of the control panel. Replace it with a new CR 2032
battery. Dispose the old battery according to local disposal rules or applicable laws.

Replacing the control unit battery

Stop the drive and do the steps in section

Precautions before electrical work

on page

before you start the work.

To replace the control unit battery:

1. Remove the M4x8 (T20) screws at the ends of the control unit.

2. To see the battery, remove the XD2D terminal block.

3. Carefully lift the edge of the control unit cover on the side with the I/O terminal blocks.

4. Carefully pull the battery out of the battery holder.

5. Carefully put a new CR2032 battery into the battery holder.

6. Close the control unit cover.

7. Tighten the M4×8 (T20) screws.

8. Install the XD2D terminal block.

Summary of Contents for ACS880-04F













































































































































































Search results

Summary of Contents for ACS880-04F

Reviews:

ABB ACS880-04F, Hardware Manual, Page: 115 / 172

Search results

Summary of Contents for ACS880-04F

Reviews: