Actual signals and parameters
175
20.03
MAXIMUM CURRENT Defines the allowed maximum motor current.
0.0 … x.x A
Current limit
0 …10·x.x
20.04
TORQ MAX LIM1
Defines the maximum torque limit 1 for the drive.
0.0 … 600.0%
Value of limit in percent of motor nominal torque.
0 … 60000
20.05
OVERVOLTAGE
CTRL
Activates or deactivates the overvoltage control of the intermediate DC link.
Fast braking of a high inertia load causes the voltage to rise to the overvoltage
control limit. To prevent the DC voltage from exceeding the limit, the
overvoltage controller automatically decreases the braking torque.
Note:
If a brake chopper and resistor are connected to the drive, the controller
must be off (selection NO) to allow chopper operation.
OFF
Overvoltage control deactivated.
0
ON
Overvoltage control activated.
65535
20.06
UNDERVOLTAGE
CTRL
Activates or deactivates the undervoltage control of the intermediate DC link.
If the DC voltage drops due to input power cut off, the undervoltage controller
will automatically decrease the motor speed in order to keep the voltage above
the lower limit. By decreasing the motor speed, the inertia of the load will cause
regeneration back into the drive, keeping the DC link charged and preventing
an undervoltage trip until the motor coasts to stop. This will act as a power-loss
ride-through functionality in systems with a high inertia, such as a centrifuge or
a fan.
OFF
Undervoltage control deactivated.
0
ON
Undervoltage control activated.
65535
20.07
MINIMUM FREQ
Defines the minimum limit for the drive output frequency. The limit can be set
only if parameter
= SCALAR.
-300.00 … 50 Hz
Minimum frequency limit.
Note:
If the value is positive, the motor cannot be run in the reverse direction.
-30000 …
5000
20.08
MAXIMUM FREQ
Defines the maximum limit for the drive output frequency. The limit can be set
only if parameter
-50 … 300.00 Hz
Maximum frequency limit
-5000 …
30000
20.11
P MOTORING LIM
Defines the allowed maximum power fed by the inverter to the motor.
0 … 600%
Power limit in percent of the motor nominal power.
0 … 60000
20.12
P GENERATING LIM
Defines the allowed maximum power fed by the motor to the inverter.
-600 … 0%
Power limit in percent of the motor nominal power.
-60000 … 0
20.13
MIN TORQ SEL
Selects the minimum torque limit for the drive. The update interval is 100 ms.
MIN LIM1
Value of parameter
.
1
AI1
Analogue input AI1. See parameter
on how the signal is converted to a
torque limit.
2
AI2
See selection AI1.
3
AI5
See selection AI1.
4
PARAM 20.18
Limit given with 20.18
5
NEG MAX TORQ
Inverted maximum torque limit defined with parameter
6
20.14
MAX TORQ SEL
Defines the maximum torque limit for the drive. The update interval is 100 ms.
MAX LIM1
Value of parameter
.
1
AI1
Analogue input AI1. See parameter
on how the signal is converted to a
torque limit.
2
Index
Name/Selection
Description
FbEq
Summary of Contents for ACS 800 Series
