manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 175

Parameters   175

22.06

Shape time acc1

Defines the shape of the acceleration ramp at the beginning 
of the acceleration.
0.000 s: Linear ramp. Suitable for steady acceleration or 
deceleration and for slow ramps.
0.001…1000.000 s: S-curve ramp. S-curve ramps are ideal 
for lifting applications. The S-curve consists of symmetrical 
curves at both ends of the ramp and a linear part in between.

Acceleration:

Deceleration:

0.000 … 1800.000 s

Ramp shape at start of acceleration.

1000 = 1 s

22.07

Shape time acc2

Defines the shape of the acceleration ramp at the end of the 
acceleration. See parameter 

22.06

 

Shape time acc1

.

0.000 … 1800.000 s

Ramp shape at end of acceleration.

1000 = 1 s

22.08

Shape time dec1

Defines the shape of the deceleration ramp at the beginning 
of the deceleration. See parameter 

22.06

 

Shape time acc1

.

0.000 … 1800.000 s

Ramp shape at start of deceleration.

1000 = 1 s

No.

Name/Value

Description

FbEq

S-curve ramp: 
Par. 

22.07

 > 0 s

Linear ramp: 
Par. 

22.06

 = 0 s

Linear ramp: 
Par. 

22.07

 = 0 s

S-curve ramp: 
Par. 

22.06

 > 0 s

Speed

Time

S-curve ramp: 
Par. 

22.08

 > 0 s

Linear ramp: 
Par. 

22.09

 = 0 s

Linear ramp: 
Par. 

22.08

 = 0 s

S-curve ramp:

Par. 

22.09

 > 0 s

Speed

Time

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands