manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 145

Parameters   145

13.14

AI3 max scale

Defines the real value that corresponds to the maximum 
analog input AI3 value defined by parameter 

13.12

 

AI3 max

.

-32768.000 … 
32768.000

Real value corresponding to maximum AI3 value.

1000 = 1

13.15

AI3 min scale

Defines the real value that corresponds to the minimum 
analog input AI3 value defined by parameter 

13.13

 

AI3 min

. 

See the drawing at parameter 

13.14

 

AI3 max scale

.

-32768.000 … 
32768.000

Real value corresponding to minimum AI3 value.

1000 = 1

13.16

AI4 filt time

Defines the filter time constant for analog input AI4. See 
parameter 

13.01

 

AI1 filt time

.

0.000 … 30.000 s

Filter time constant.

1000 = 1 s

13.17

AI4 max

Defines the maximum value for analog input AI4. The input 
type depends on the type and/or settings of the I/O 
extension module installed. See the user documentation of 
the extension module.

-22.000 … 22.000 
mA or
-11.000 … 11.000 V

AI4 maximum value.

1000 = 1 unit

13.18

AI4 min

Defines the minimum value for analog input AI4. The input 
type depends on the type and/or settings of the I/O 
extension module installed. See the user documentation of 
the extension module.

-22.000 … 22.000 
mA or
-11.000 … 11.000 V

AI4 minimum value.

1000 = 1 unit

No.

Name/Value

Description

FbEq

AI

 (scaled)

AI

 (mA/V)

13.14

13.12

13.13

13.15

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands