The motor thermal protection model supports thermal memory retention and speed
sensitivity. The user can tune the thermal model further by feeding in additional motor
and load data.
The most common temperature sensor types are thermal switch (for example Klixon),
PTC or Pt100.
For more information, see the firmware manual.
Protecting the drive against ground faults
The drive is equipped with an internal ground fault protective function to protect the unit
against ground faults in the motor and motor cable. This function is not a personnel
safety or a fire protection feature. See the firmware manual for more information.
■
Residual current device compatibility
The drive is suitable to be used with residual current devices of Type B.
Note:
As standard, the drive contains capacitors connected between the main circuit
and the frame. These capacitors and long motor cables increase the ground leakage
current and may cause nuisance faults in residual current devices.
Implementing the emergency stop function
You can order the drive with an emergency stop function (option).
See the appropriate option manual for more information.
Manual code
(English)
User’s manual
Option
code
Emergency stop, stop category 0 (Q951) for ACS580-07,
ACH580-07 and ACQ580-07 drives user's manual
+Q951
Emergency Stop, Category 0 (Q963) without opening main
contactor with safety relay for ACS580-07, ACH580-07 and
ACQ580-07 drives user's manual
+Q963
Implementing the Safe torque off function
See chapter
The Safe torque off function (page 273)
.
Implementing the power loss ride-through function
If the incoming supply voltage is cut off, the drive will continue to operate by utilizing
the kinetic energy of the rotating motor. The drive will be fully operational as long as the
motor rotates and generates energy to the drive.
If the drive is equipped with a main contactor (F250), it restores the drive input
power after a short break. The power supply for the contactor control circuit is buffered.
Guidelines for planning the electrical installation 97
Summary of Contents for ACQ580-07
