ABB A175-M66 Operating Manual Download

Page: 84 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.5 Removing the compressor casing

HZTL4033_EN

Rev.H

July 2021

9.5

Removing the compressor casing

Removing wall insert

Fig. 37: Removing wall insert

1. Loosen screws (72011) and remove with washers (72008).

2. To secure the wall insert, screw in one screw (72011) a third of the way.

3. Press off wall insert with three screws (72011) until the lifting device (90190) and the fix-

ing segment (90192) can be fitted.

4. Fit the lifting device (90190) and the fixing segment (90192) to the flange of the wall in-

sert (77000) using the screws (90197) and washers (90198).
Depending on the hole pattern of the wall insert (77000), the screws (90197) cannot be
fitted symmetrically.

5. Put on shackle (90195) and fasten to lifting gear.

6. Remove locking screw (72011).

Page

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands