ABB A175-M66 Operating Manual Download | Manualshive

Page: 121 / 150

background image

Operation Manual / A170-M.. - A175-M..

10 Taking a turbocharger out of operation / 10.1 Possible emergency
repairs

© Copyright 2021 ABB. All rights reserved.

HZTL4033_EN

Rev.H

July 2021

10

Taking a turbocharger out of operation

10.1

Possible emergency repairs

CAUTION

Machine damage in emergency operation

The assembly of the locking device on the turbocharger is only permissible
in emergencies. It is not permitted to lock the rotor for an engine test. Seri-
ous damage to engine or property can be caused by non-compliance with
the regulations in the event of an emergency.

u

The permissible turbocharger speed for the unlocked turbocharger may
not exceed n

Bmax

. Take note of the rating plate.

u

After locking the turbocharger, contact an ABB Turbocharging Service
Station and find the nearest port.

u

Observe the safety regulations.

u

Follow the directives of the enginebuilder.

WARNING

Danger of fire and explosion due to lubricating oil leaks

Leaking oil may ignite on hot surfaces. This can result in serious injuries to
personnel or fatal accidents.

u

Cordon off danger area.

u

Raise the alarm and, depending on the situation, stop the engine.

u

Seal the oil leak.

u

Soak up oil and dispose of in an environmentally compatible manner.

Wear safety gloves to protect against thermal hazards.

If damage has occurred to the turbocharger and the engine has to be brought back into op-
eration again as quickly as possible, the following emergency repair options are available:

¡

Lock the rotor

¡

Attach a cover plate

¡

Blank off the inlet and outlet flanges of casings

¡

Bypass the turbocharger

Page

119

/

147

«
...
119
120
121
122
123
...
»

Summary of Contents for A175-M66























































































































































Reviews:

No comments

Related manuals for A175-M66

Brand: FAAC Pages: 22

2.7-litre V6 Biturbo

Brand: Audi Pages: 72

Brand: Nissei Pages: 16

Brand: Key Automation Pages: 44

Brand: Brother Pages: 42

Brand: Volvo Penta Pages: 132

Sterndrive TDI 3.0L

Brand: MerCruiser Pages: 119

Brand: HIOTH TECHNOLOGY Pages: 5

BREVINI T Series

Brand: DANA Pages: 46

BREVINI E 100 Series

Brand: DANA Pages: 50

Brand: O.S. Speed Pages: 20

Brand: O.S. engine Pages: 23

Brand: Honda Pages: 32

Brand: Honda Pages: 48

Brand: Honda Pages: 56

Brand: KRESS Pages: 170

Xicoy AU-107K ECU

Brand: Wren Turbines Pages: 12

Brand: LONCIN Pages: 219

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands