ABB A130-H57 Operation Manual Download

Page: 94 / 124

Operation Manual / 4 Product description / A130-H.. - A140-H

8 Dismantling and fitting / 8.5 Removing the gas outlet flange

HZTL4030_EN

Rev.F

February 2020

Gas outlet flange with 3 press-off screws

CAUTION

Cracks in the gas outlet casing

Non-observance of the action steps described can lead to inadmissible
cracks on the gas outlet flange.

Observe the maximum tightening torques when pressing off.

Follow the action steps described.

Only dismantle the gas outlet flange if this is necessary for service work.

If necessary: Treat the centering seat with rust remover through the press-off threads
and the clearance holes.

Mark the casing position for assembly.

Fig. 31: Dismantling the gas outlet flange

Product

Press-off screws (strength 8.8) *

Tightening torque

A130

3 x M 8 x 20

≤

20 Nm

A135

3 x M10 x 25

≤

40 Nm

A140

3 x M12 x 30

≤

65 Nm

Table 32: 3 press-off screws

* not included in the ABB Turbo Systems scope of delivery

1. Press off and remove the gas outlet flange (57002) with screws (01) according to the

table. If it is not possible to press off the gas outlet flange with the maximum tightening
torque, contact an ABB Turbocharging Service Station.

2. If present: Remove the C-ring (57003).

Page

Summary of Contents for A130-H57





























































































































Search results

Summary of Contents for A130-H57

Reviews:

Related manuals for A130-H57

Brands by name

Popular brands

ABB A130-H57, Operation Manual

Search results

Summary of Contents for A130-H57

Reviews:

Related manuals for A130-H57

Brands by name

Popular brands