ABB 1ZSC902110-AAA Installation And Commissioning Manual Download

Page: 52 / 84

Installation and commissioning guide

1ZSC000563-AAF EN, REV. 4, 2021-06-23

4.9 Grounding of the bushing flange

Overview

The bushing flange must be grounded to the transformer tank. This prevents electrical discharge between the
bushing flange and the transformer tank under normal service conditions.

DANGER!

Make sure that the grounding is correct. An unsatisfactory grounding can cause damage to
equipment, or death to personnel.

Procedure with a flexible cable

Clean the contact surfaces.

Put a flexible cable (64) between the grounding
hole in the bushing flange and a grounding point
on the transformer.

G006973

Apply a large quantity of Mobilgrease 28 to the bolt (50).

CAUTION!

The quality of the bolt is important, stainless steel of A4-80 quality is recommended.

NOTE!

Or use a lubricant similar to Mobilgrease 28.

Install the bolt (50).

Torque

M12: 40 Nm

Connect the other end of the flexible cable (64) to the transformer.

NOTE!

This makes an electrical connection between the bushing and transformer tank, keeping
them at the same potential.

End of instruction

Summary of Contents for 1ZSC902110-AAA





















































































Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands

ABB 1ZSC902110-AAA, Installation And Commissioning Manual

Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands